-
Description
36V 750W 48V 1000W 52V 1200W 14", 16", 18", 20" Integral Rear Wheel Conversion Kits: 14", 16", 18", 20"
36V 750W / 48V 1000W / 52V 1200W 14"/16"/18"/20" Integral Rear Motorized Wheel (single-speed Freewheel / 7-speed Freewheel)
14x2.5"/ 16x2.5"/ 18x2.5"/ 20x2.5" Tire and tube installed
36V/48V/52V 35A 15 MOSFET 3-mode Sine Wave Controller
Controller Bag
UKC1 Color Display (with 5V USB output)
Half-bar Twist Speed Throttle with Electric Key Lock 2ea. Handlebar Grips
Brake Levers (Left and Right)
Pedelec Sensor (PAS)Motor Specification:
1) High Motor Efficiency: max 88.7% (Save Power)
2) Torque: max torque 40 N.m.
3) RPM: max 450
4) Speed: 0-50 km/h (different wheel size, road & weather condition and rider's weight will have different speed)
5) Frame Dropout: 135mm Rear Wheel hub motor
6) Support standard 6-hole type disc brake
7) Rear Integral Wheel
Controller Specification:
1) 36V/48V/52V 35A 15 MOSFET 3-mode Sine Wave Controller
2) Rated Voltage: DC36V or 48V or 52V universal
3) Rated Current: 17A
4) Max Current: 35 +/- 1A
5) Speed set: 1-4.2V
6) Brake Input: Low Level
7) Low Voltage Protection: DC30/40/43V +/- 0.5V
8) Compatible with LCD Display or without Display (need to plug LCD jumper connector)
9) Size: 212x86.5x48.5mmLCD Specification:3.5 inch IPS screen
1) 24V/36V/48V/52V/60V/72V battery supply
2) Rated operating power : 1W
3) Max operating power : 5W
4) USB charging port : 5V 500mA
5) Off leakage current < 1uA
6) Support current to controller : 100mA
7) Size:111.1*66.8*82.8mm
8) Waterproof grade:IP65
9) Operating temperature : -20~70℃,
10) Storage temperature : -30~80℃Installation Guidance:
1) Unscrew the existing rear wheel screws, remove your rear wheel;
2) Install the motorized wheel and fasten screws;
3) Attach LCD, Brake lever and throttle;
4) Put Controller at suitable position and connect all wires.
5) Turn on battery, throttle key and LCD, set correct value from LCD
Correct wheel size setting: according to your wheel size
Correct motor magnet quantity setting: set it at 46
Save all value and restart LCD displayFAQ:
1. How shall I match my motor for first time use? (Very Important)
(Please check Controller Connection Diagram and Manual, Page 1)
1). Lift your motor wheel off ground (very important)
2). Connect Self-learning plug 6-8 seconds
3). You will see motor wheel rotate slowly
4). Please check whether rotation direction is correct
(a). If correct direction, then keep 6-8 seconds, then disconnect
(b). If reverse direction, then disconnect and plug again till get correct rotation direction, then keep 6-8 seconds, then disconnect
5). Motor and Controller Pairing finished!
2. Can I use this controller without display?
Yes, you can use this controller without display, just need to connect jumper connector (Please check Controller Connection Diagram and Manual, Page 4, point No.3)
3. How can I limit speed?
In some countries, below 25km/h speed is required on road, you can switch on/off speed limit function by connecting a simple switch to controller speed limit plug, or you can even connect jumper connector to always limit speed (Please check Controller Connection Diagram and Manual, Page 9-10, point No.12)
Manual Download:
1. Controller Connection Diagram and Manual Download
2. UKC-1 Display Manual Download
-
Product reviews can be carried out after the member login, please click here to login