We use cookies to improve your online experience. By continuing browsing this website, we assume you agree our use of cookies.
X
Your position: Home / Online Shopping Mall / eBike Electronic Parts / eBike Controller
PDF Format
  • Description

    60V-72V 5000W-7000W 100Sine Wave Intelligent Controller with/Without Colorful LCD Display for eBike Electric Bike
     
    Very important Notice:
    This controller can only work without display or with our display, please never use it with your own display (because program is different)

    Why self-learning?
    Self-learning Function:
    (1). Wrong color wires combination of 5-hall sensor wires (But please ensure hall sensor is good, red and black hall sensor wires must be connected correctly) between motor and controller, doesn’t matter, self-learning process can correct it!
    (2). Wrong color wires combination of 3-phase wires between motor and controller, doesn’t matter, self-learning process can correct it!


    Parts Including:
    1. 24 MOSFET 60V 72V Universal Voltage 5000W-7000W Intelligent Sine Wave Controller 
    2. XT150 Male Connectors x 3pcs, QS8 Female Connector x 1pc
    3. 36V, 48V, 52V, 60V, 72V UKC1 Colorful Display (Optional)

     
    Advantage:
    1. Sine Wave Controller which support self-learning and smart match with each motor through self-learning, works with high efficiency, less noise, and lower energy consumption, which makes your electric vehicles or electric motorcycles more comfortable and easier to control, give you best pedal experience
    2. Universal Input Voltage Range: 60V/72V
    3. Work with or without display
    4. Parameter setting via display
    5. All protection make it long life and safe: over/under voltage, over current, over load, over heating, anti-runaway, locked-motor protection
    6. Multi functions: Work with hall sensor mode or non-hall mode, smart match with different motor, 3/5/9-speed level for throttle and PAS, Current limit, Speed limit, Reverse, Push Assistant, Anti-thief, Regenerative Braking (Can set different level: Off, Standard, Weak, Strong), Speed detecting (Magnet quantity simulated or internal speed sensor) and etc.
    7. Best heat sinking with Aluminium Case
    8. Black anodized Aluminium Controller Case against scratch
     
    Technical Data:
    General Specification:
    1. Rated Power: 60V 3000W/ 72V 3600W
    2. Peak Power: 60V 6000W/ 72V 7200W
    3. Brake: Low Voltage Brake
    4. Alarm: Low Voltage Alarm
    5. Rotor Position Detecting Method: Hall sensor
    6. 3-Phase Connectors: XT150 Female Plugs
    7. Power Input Connector: QS8 Male Plug
    8. 3-Phase and Power Input Cable Size: 7AWG (10mm2)

    9. Size: 252x121x74mm
    10. Net Weight: 1900g
    11. Waterproof Grade: IP65

    LCD Specification: 3.5 inch IPS screen
    1) Input Voltage: 24V/36V/48V/52V/60V/72V
    2) Rated operating power: 1W
    3) Max operating power: 5W
    4) USB charging port: 5V 500mA
    5) Off leakage current: < 1uA
    6) Support current to controller: 100mA
    7) Size: 111.1*66.8*82.8mm
    8) Waterproof grade: IP65
    9) Operating temperature: -20~70℃, 
    10) Storage temperature: -30~80℃
     
    FAQ:
    1.  How shall I match my motor for first time use? (Very Important)
    (Please check Controller Connection Diagram and Manual, Page 1)
    1). Lift your motor wheel off ground (very important)
    2). If you connect with display, please make sure PAS/Throttle Speed Level is at any level more than 0 level
    3). Connect Self-learning plug 6-8 seconds
    4). You will see motor wheel rotate slowly
    5). Please check whether rotation direction is correct
    (a). If correct direction, then keep 6-8 seconds, then disconnect
    (b). If reverse direction, then disconnect and plug again till get correct rotation direction, then keep 6-8 seconds, then disconnect
    6). Motor and Controller Pairing finished!

    2. Can I use this controller without display?
    Yes, you can use this controller without display, just need to connect jumper connector (Please check Controller Connection Diagram and Manual, Page 4, point No.3). But if you want to have and change ABS setting (Reg. function) and use Cruise function, have to buy our UKC1 display together. 

    3. How can I limit speed?
    In some countries, below 25km/h speed is required on road, you can switch on/off speed limit function by connecting a simple switch to controller speed limit plug, or you can even connect jumper connector to always limit speed (Please check Controller Connection Diagram and Manual, Page 6, point No.8) 
     
    4. How can I active Regenerative braking function?
    This function need to use together with UKC1 display, please enter "Advanced Setting",  there is "ABS Levels" option (0-3). "0" means turn off; "1" means weak; "2" means standard; "3" means strong--- we don't recommend to use 3, it is too strong, we will not be responsible for controller or motor damage due to this setting (ABS level=3) 

    5. How can I use cruise function?
    This function need to use together with UKC1 display, please keep throttle at speed not change, and long press "Down" key at same time will active cruise function, press any key or operate brake or throttle to change speed will stop Cruise function.
     
    Manual Download:
    1. Controller Connection Diagram and Manual Download
    2. UKC-1 Display Manual Download

60V-72V 5000-7000W 100A Sine Wave ebike Controller with/without Colorful LCD Display (Regenerative function for 60V/72V)

Self-learning for hall sensor and 3-phase;
Rated Power: 60V 3000W/ 72V 3600W;
Peak Power: 60V 6000W/ 72V 7200W
Sold:
4
$199.99
30% OFF
  • Display:
+
-
Wholesale
Quantity
Price ( $ )
1-4
$139.99
5-9
$135.99
10-19
$129.99
20-49
$125.99
50+
$119.99
(96 available)
Shipping Cost:
to
Estimated Delivery Time:
Please select the country you want to ship from
Please select the information you wantX
Message Us