We use cookies to improve your online experience. By continuing browsing this website, we assume you agree our use of cookies.
X
Your position: Home / Online Shopping Mall / eBike Conversion Kits / 500W-2000W Gearless Hub Motor Wheel Kits
PDF Format
  • Description

    72V 80A 3000-4000W 29" rear wheel conversion kits with UKC1 Color Display

     

       
    Parts Including in this kit:
    1. 72V 3000-4000W Brushless Gearless Rear Hub Motor Wheel (without tire and tube) (with thread-on 7-speed freewheel. Reinforced double-layer aluminum alloy rim,12G reinforced black spokes, 3mm2 Motor Extension cable with waterproof plug), MTX39 29" Wheel
    2. 48-72V 80A sine wave controller (support both hall sensor motor and non hall sensor motor)
    3. 24V/36V/48V/52V TFT UKC1 Color display
    4. Full Bar Twist Throttle
    5. Hydraulic Disc Brake
    6. PAS Pedelec Sensor
    7. Controller Bag
     

     

    Motor Specification:
    1) High Motor Efficiency: max 88% (Save Power)
    2) Torque: max torque 80 N.m.
    3) RPM: max 600
    4) Max Speed: 80-85km/h (different road&weather condition and rider's weight will have different speed)
    5) Hub Width (Frame dropout requirement for 7-speed): 142mm rear thread-on hub motor
    6) Support standard 6-hole type disc brake
    7) Rear Wheel with Shimano 7-speed freewheel
     

    Controller Specification:
    1) 48-72V 80A 18 MOSFET 3-mode Sine Wave Controller
    2) Rated Voltage: DC48V/52V/60V/72V universal
    3) Rated Current: 50A
    4) Max Current: 80 +/- 1A
    5) Rated Power: 72V 3600W
    6) Peak Power:  72V 5760W
    7) Speed set: 1-4.2V
    8) Brake Input: Low Level
    9) Low Voltage Protection: DC40V/43V/50V/60V +/- 0.5V
    8) Compatible with our LCD Display or without Display (need to plug LCD jumper connector)
    9) Size: 275x121x62mm
    10) Weight: 2.05kg

     

    UKC1 Color display Specification:
    1)  24V-72V universal
    2) Function: max 5-speed level PAS, speed display, speed limit, Cruise, 5-speed level throttle, optional Regenerative braking function
    3) With press key button: Up, Down, Power 
    4) Can be vertical or horizontal
    5) 5V USB Output


    Advantage:

    1.FOC-180° sinusoidal drive controller applied to BLDCM or PMSM.
    2.It takes only 2-3 minutes for the motor to be well matched on its best electronic angle at the first time.
    3.The motor torque ripple will be reduced to the minimum, so as to ensure electric vehicle to run without any noise      and vibration, smoothly, and comfortably.
    4.The precise current ring can provide accurate torque input to meet the requirement of large torque output during      vehicle starting and climbing.
    5.The controller enjoys high efficiency due to space vector converter control algorithm which can effectively reduce    the temperature rise of controller and extend battery life mileage
    6.Built-in various protection: locked-rotor protection, over-current protection, overload protection, over-temperature    protection, speed protection, over-voltage protection, under-voltage protection and so on, effectively ensuring the    safety of electronic control system and vehicle.
    7.System status and fault intelligent management system can effectively monitor the current system operating mode external input state, the case of system failure, and the LED flashes at the same time to facilitate the       diagnosis and maintenance.
    8.Multi peripheral interfaces: reverse, cruise, anti-theft electronic brake, etc.
    9.Parameter modifications and settings are available through Mobile phone via Bluetooth or computer via USB data  cable
    10.CAN BUS is optional to communicate with body instrument and BMS
     

    FAQ:

    1. Can I use this controller without display?

    Yes, you can use this controller without display, just need to connect jumper connector (Please check Controller Connection Diagram, Page 3, point No.5) 

    2. Why when I turn on Display, it always show "Error 30H"?

    Please kindly check whether you also connect communicaton plug (Please check Controller Connection Diagram, Page 6, point No.12) 

    3. Why when I connect Bluetooth Module or USB Cable, it always show "Connection Failure"?

    Please kindly check whether you disconnect communicaton plug (Please check Controller Connection Diagram, Page 6, point No.12), and also reconnect Bluetooth Module or USB Cable to ensure good connection.

    4. If I want to use your controller work with my motor, what shall I do?

    To get best efficiency, we recommend you to match your motor with our controller firstly (Please check Controller Manual-APP Version, Page 5-9, or check Controller Manual-USB Cable, Page 6-7)

     

    Manual and Driver Program Download:

    1. Common Error Code Definition and Solution Download

    2. Controller Connection Diagram Download

    3. Controller USB Connection Driver, Application Program and Manual (Controller connect with computer by USB Cable)

    (1). USB Driver Download:

          Controller USB Connection Driver Download (32bit)

          Controller USB Connection Driver Download (64bit)

    (2). Controller Application Program for Computer (connect by USB Cable) Download

    (3). Controller Manual Download (Computer Version connect by USB Cable)

    (4). Controller Setting and Motor Pairing Video

    4. Controller Manual/ Bluetooth App Manual (Controller connect with mobile phone by Bluetooth Module)

    (1). Controller Manual Download (APP Version connect by Mobile phone Bluetooth)

    (2). Bluetooth Module Manual Download

    5. UKC-1 Display Manual Download

72V 80A 3000-4000W 29" rear wheel conversion kits with UKC1 Color Display ship by sea to door

72V 80A 3000-4000W 29" rear wheel conversion kits with UKC1 Color Display
Sold:
1
$639.99
28% OFF
  • Wheel Size Options:
  • Throttle Type:
  • Display Options:
  • Brake:
  • Freewheel:
+
-
(2 available)
Shipping Cost:
to
Estimated Delivery Time:
Please select the country you want to ship from
Please select the information you wantX
Message Us